Dileb

News

As the committed company that we are, we will always keep you up to date. You will find all Dileb news here:

Insights into production
Some impressions of our production with a total area of approximately 8,000 square metres distributed over 5 halls with machining possibilities of up to 36,000 mm in length and unit weights of up to 200,000 kg.

continue reading

Stress relief annealing at DILEB
On a sunny day, we start up the furnace In our annealing furnace, components with dimensi...

continue reading

New year reception 2023
DILEB Maschinenbau GmbH & Co. KG welcomes the new year with a get-together.   We look back on the year 2022 with many challenges and busy months. The entire employees celebrated the new year and the positive outlook into a promising future:

continue reading

Expansion of our machine park
Preparations for the new foundations run at full speed. The old foundation has been cut out and removed. Now the holes of the foundations for our new machines are being dug. Vertical lathe:    Machining diameter: 3,500 mm; max....

continue reading

Insight into the machining Process
In this short clip we give a brief insight into our production. Here, holes with a diameter of 80 mm are drilled into a frame plate (14.4 tons) with the dimensions: Length x width: 5,890 x 4,640 mm and a thickness of 90 mm.   DILEB

continue reading

DILEB @ IBA´s anniversary 35(+1)
Congratulations to IBA for their 35(+1) anniversary! #thankyou very much fo...

continue reading

#weridewith#bikeleasing - For the sake of our health and the environment
We invest in the future of the company and our employees. Since September 2022, our employees have the opportunity to lease a company bicycle. This way, you can not only save a lot compared to a private purchase, but also do something for your healt...

continue reading

Coming soon...
Preparations for the expansion of our machine park in the form of two new machines are in full swing. Soon the time will come and a new rotary carousel machine (max. table load 50,000 kg) and a new deep hole drilling machine (max. table load 25,000 ...

continue reading

DLRG
On 16.09.2022 the time had finally come. As one of the sponsors of the DLRG local group Dillingen/Saar e. V., we were able to take delivery of the new 2-t box trailer.  This trailer enables the DLRG to transport materials for the water rescue service ...

continue reading

Speciality: Ladles + Converter
Today, together with our logistics partner, we were once again able to send 4 casting ladles and a lower section of a converter on their journey to our customers: 4x casting ladle with a capacity of 400 t liquid crude steel with the dimensions ...

continue reading

Speciality: Ladles
By using our combined boring mill, we are able to machine parts with a length of up to 36 meters.

continue reading

Heating plates
One of our "standard products" are heating plates for various industries. The following series of pictures shows the production process of the heating plates in our company. 

continue reading

Speciality: Ladles
Today, again heavy parts for the steel industry leave our factory at DILEB MASCHINENBAU GmbH & Co. KG in Lebach, Saarland, Germany. Two casting ladles and a upper part of the converter begin their journey to our customer early in the morning in bright...

continue reading

Speciality: Ladles
One of our specialities: heavy duty ladles for steelworks... Four casting ladles, each with a capacity of 270 t or 400 t of liquid steel, have left our factory DILEB Maschinenbau GmbH & Co. KG in Lebach and are now on their way to the customer.

continue reading

World´s largest roll forming machine
A very special challenge for our specialists from production and especially logistics was the recently delivered order for the production of the main components for a pipe welding system. In the future, this system will produce pipes with a diameter...

continue reading

XXL-sized press frames
Once again, we were able to prove our efficiency by producing two XXL-sized press frames for one of our long-standing customers. The frames are used in the plastics industry. What's special is how gigantic the dimensions are. With a frame ...

continue reading

Recertification ISO 9001
Our ISO 9001:2008 certification has been successfully recertified to the current ISO 9001:2015 standard. You can download our new certificates in German and English in the Download section.  

continue reading

Punctual delivery of press frame
DILEB was once again able to prove its efficiency by punctually delivering a sophisticated press frame. The frame with a unit weight of 40 tons belongs to a highly sophisticated press series for a well-known automotive supplier in Germany.

continue reading

Up to 200t
individual unit weight
8000m²
production area
Up to 36m
of machining
Since 1969
top quality
Sie müssen Marketing-Cookies akzeptieren um Google Maps anzusehen.
© 2023 DILEB Maschinenbau GmbH & Co. KG | Dillinger Str. 130 | 66822 Lebach / Saar
Imprint  â€¢  Data protection  â€¢  Disclaimer